bike-maintenance-cadence
Use when you ride a bike and want to know WHAT to maintain WHEN: converts ridden km/weeks/conditions into a dated service schedule per component (chain wear, cassette, brake pads, cables, tires, bearings, suspension, drivetrain deep-clean), prices wear parts by component-lifetimes math, and diagnoses drivetrain noises/brake rub/shifting ghosts. Solves the 'chain skipped, now the cassette is dead too' cascade problem.
Bike Maintenance Cadence
Overview
Bikes fail by cascade. A $20 chain ridden 500 km past its wear limit grinds the cassette ($40–90) and chainrings ($30–120) into matching its stretch — then the "sudden" replacement bill is $150+ instead of $20, three times a year. The entire economics of bike ownership is detecting wear at the chain-checker stage, and almost nobody owns a chain checker or knows their component lifetimes in km.
This skill converts how you actually ride (weekly km, weather, storage, terrain) into a dated, per-component service calendar: when to measure chain wear (0.5% / 0.75% / 1.0% thresholds and what each means), when pads, cables, tires, bearings, and (if fitted) suspension are due. It prices the wear-parts budget per year from component lifetime tables, and routes the common failure noises to causes with a 10-minute diagnostic sequence before parts-shopping.
The multiplier effect: wet/urban/winter riding roughly doubles drivetrain wear; dry garage storage halves cable corrosion. The schedule reflects YOUR conditions, not the manual's generic "every 500 km."
When to Use
- Setting up maintenance for a new (or new-to-you) bike — first calendar + tool list
- "It's been making a noise / skipping / rubbing" — diagnostic router first, then maintenance
- Budgeting: what does this bike cost per year in wear parts at my km?
- Returning rider dusting off a bike after years — the revival safety checklist
- Deciding repair-vs-replace on a worn drivetrain (partial vs full replacement rules)
- Pre-season / pre-big-ride audit (the week-before checklist)
Don't use for: e-bike firmware/motor/battery service (manufacturer territory — though the mechanical parts here still apply), suspension internals beyond seal/fork service intervals (specialist tools), or carbon frame crack assessment (professional inspection — do not ride a suspected cracked frame).
Component Lifetimes (typical, adjustable by conditions)
| Component | Life (good conditions) | Wet/winter/urban | Check method |
|---|---|---|---|
| Chain | 3,000–5,000 km | 1,500–2,500 km | wear gauge 0.75% |
| Cassette | 2–3 chains | 1–2 chains | hook-shaped teeth, skip under load |
| Chainrings | 3–4 chains | 2–3 chains | shark-fin teeth |
| Brake pads (rim) | 2,000–4,000 km | 1,000 km | visual wear line |
| Brake pads (disc, resin) | 2,000–5,000 km | 1,000–2,000 km | pad material ≥ 0.5 mm above backing |
| Disc rotors | 10,000+ km | — | thickness gauge; min stamped (usually 1.5–1.8 mm) |
| Cables + housing | 1–2 yr | 6–12 mo | fraying, sluggish return |
| Tires | 3,000–6,000 km rear / 2× front | less | tread squaring, cuts, casing threads |
| Tubes | until punctured | — | patch vs replace economics |
| Bottom bracket | 5,000–10,000 km | less if pressure-washed | creak under load, side-play |
| Wheel bearings | 5,000–10,000 km | — | spin + grab test, rock wheel |
| Headset bearings | 1–2 yr | less if rain | index creak, notchy steering |
| Suspension seals/fork oil | 50 hrs service / 100–200 hr full | — | manufacturer hours meter |
| Tubeless sealant | 2–4 mo | — | shake check / top-up |
The one tool that pays for itself in a week: a chain wear gauge ($10). Everything else follows from catching the chain at 0.75%.
The Cascade Rules (money-saving doctrine)
- Replace chain at 0.75% wear → cassette usually survives (2–3 chains per cassette).
- Chain hits 1.0%+ (≈ 0.5% too late): budget chain + cassette together. Riding further eats chainrings.
- New chain on worn cassette = skipping under load in the 3–4 most-used cogs within a week. That skip IS the cassette's verdict — don't blame the chain.
- Mixed-generation parts (11s chain on 10s drivetrain etc.): don't. Compatibility is speed-generation specific.
- When replacement total > ~40% of a decent used bike's value, consider the whole-drivetrain-new or bike-replacement math honestly.
Symptom Router (diagnose before buying)
- Skipping under load → chain/cassette wear (measure first), or stiff link (flex-check), or derailleur B-gap/h-limit off.
- Chain suck / front derailleur jamming → worn chainrings, chain too wide/narrow mismatch, or grimy chain.
- Brake rub (disc) → caliper centering (loosen bolts, squeeze lever, retighten), rotor true (slight trueness tolerable >0.3 mm wobble fix), or bent rotor from transport.
- Spongy disc lever → air in line (bleed) or pad glaze (sand lightly) — NOT "more cable tension."
- Grinding/crunch on pedaling → BB bearings (side-play test), or pedal bearings, or rear DER pulley seizures. Isolate: does it happen in every gear standing vs seated?
- Click every crank revolution → chainring bolts, pedal threads, BB, or shoe cleat. Tighten ring bolts first — free fix, most common.
- Wheel thump/click per revolution → spoke nipple looseness, tire bead seat, or hub bearings. Spin test locates the sector.
- Indexing ghost-shifts in 2 cogs only → cassette wobble/loose lockring or bent DER hanger — the hanger is the sacrificial part; alignment tool or replace ($15 vs frame).
Common Pitfalls
- Pressure-washing — forces water+grit into bearings, BB, and suspension seals; kills more parts than riding does. Bucket + brush + degreaser on the drivetrain only.
- Lube on a dirty chain — makes grinding paste. Wipe → degrease when black → dry → lube → wipe. 90% of chain life is the wipe.
- Over-tightening — especially stem/steerer carbon (torque wrench + carbon paste at 5 Nm typical) and BB cups. Split the difference by feel only if no torque data.
- New cables on worn housing (or the reverse) — replace as pairs, or the sluggishness survives and you blame the wrong part.
- Ignoring the front brake because "the back one stops me." Front = 70% of stopping power; pads wear there first.
- Resin pads on long descents glaze/fade — for sustained mountains, sintered pads. For dry flat commuting, resin is quieter and grabs sooner.
- Tubeless "set and forget" — sealant dries to a latex pancake in 2–4 months; top up or the system silently becomes a worse clincher.
- Storage wet in a shed — cables and chain rust between rides; wipe chain, and a $5 cover beats a $60 cable set yearly.
Verification Checklist
- Weekly/monthly km stated or estimated; conditions multiplier applied
- Dated next-service entries per component, not vague intervals
- Chain-wear measurement instruction included (0.5/0.75/1.0 thresholds)
- Cascade check: if chain > 1.0%, cassette priced into the plan
- Annual wear-parts budget computed from lifetime table × your km
- Symptom router run BEFORE any parts purchase advice
- Safety-critical items flagged (brakes, tires, headset, wheel integrity, carbon torque)
One-Shot Recipe
# 120 km/week, urban commuting, rain, stored in a shed
python3 scripts/bike_cadence.py schedule --km-week 120 --conditions wet --storage shed \
--last-service 2026-08-01
# → dated calendar: chain check NOW (wet multiplier), pads in 6 wk, cables 4 mo...
# what does my riding cost in wear parts?
python3 scripts/bike_cadence.py budget --km-week 120 --conditions wet --disc
# the classic: skipping under load, what do I check in what order?
python3 scripts/bike_cadence.py diagnose --symptom skip-under-load
- Downloads
- Security audit
- Pass
- Last updated
- 2w ago
- Current version
- v1.0.0
- License
- MIT-0
