Isis Analysis

IS-IS protocol analysis with adjacency diagnosis, LSPDB analysis, level 1/2 routing validation, and NET address verification. Multi-vendor coverage for Cisco IOS-XE, Juniper JunOS, and Arista EOS with protocol-first diagnostic reasoning.

IS-IS Protocol Analysis

Protocol-reasoning-driven analysis skill for IS-IS adjacency formation, LSPDB integrity, level 1/2 routing, and NET address validation. Unlike device health checks that compare counters against thresholds, IS-IS analysis requires interpreting adjacency state machines, validating NET addressing, verifying DIS election, and assessing LSP flooding across the link-state domain.

Commands are labeled [Cisco], [JunOS], or [EOS] where syntax diverges. Unlabeled statements apply to all three vendors.

When to Use

• IS-IS adjacency not forming or stuck in Init state
• Unexpected route changes or missing routes in the IS-IS domain
• Level 1/2 boundary issues — suboptimal routing, missing L1 default, route leaking not working as intended
• LSPDB inconsistency — LSP count mismatch between neighbors, unexpected purges, sequence number anomalies
• NET address conflict or system ID duplication causing LSP wars
• Post-change verification of IS-IS configuration (new interfaces, area changes, metric style migration, authentication rollout)
• DIS election not converging on broadcast segments

Prerequisites

• SSH or console access to the router (read-only privilege sufficient)
• IS-IS process running on the device with at least one active interface
• Knowledge of expected level topology: which routers are L1-only, L2-only, or L1/L2, and which areas (area addresses) are in use
• System IDs and NETs known or documented — NET format is AFI.areaID.systemID.NSEL (e.g., 49.0001.1921.6800.1001.00)
• Awareness of configured authentication per level and interface (none, MD5, HMAC-SHA)

Procedure

Follow this diagnostic flow sequentially. Each step builds on data from prior steps, moving from broad inventory to targeted diagnosis.

Step 1: IS-IS Instance and Interface Inventory

Verify IS-IS is running and confirm which interfaces participate at each level.

[Cisco]

text

show isis interface brief

[JunOS]

text

show isis interface

[EOS]

text

show isis interface brief

Record each interface: level enablement (L1, L2, or L1/L2), circuit type (point-to-point or broadcast), metric, hello interval, and hold time. Compare against expected design — every interface that should participate must appear. An interface missing from output means IS-IS is not enabled on it (missing under the IS-IS router config or interface config). Verify the NET address with show isis protocol (Cisco), show isis overview (JunOS), or show isis summary (EOS) — the NET must be correctly formed and unique.

Step 2: Adjacency Assessment

List all IS-IS adjacencies and interpret their state.

[Cisco]

text

show isis neighbors

[JunOS]

text

show isis adjacency

[EOS]

text

show isis neighbors

Compare the neighbor list against expected topology. For each adjacency, verify:

• State: Up is healthy; Init means one-way (hellos received but this router's SNPA/system ID not in the neighbor's hello). Down means no hellos received.
• Level match: L1 neighbors must share at least one area address. L2 neighbors can be in different areas — only system ID uniqueness is required. An L1-only router will not form L2 adjacency with an L2-only router.
• Circuit type: On broadcast segments, check DIS (Designated Intermediate System) election. Unlike OSPF DR/BDR, IS-IS DIS election is preemptive — a new router with higher priority takes over immediately.
• DIS status: On broadcast segments, identify which router is DIS for each level. DIS sends CSNPs every 10 seconds and creates the pseudonode LSP.

Step 3: NET Address Validation

Verify NET format and system ID uniqueness across the domain.

[Cisco]

text

show isis protocol | include NET|System

[JunOS]

text

show isis overview | match "NET|System"

[EOS]

text

show isis summary | include NET|System

Validate NET structure:

• AFI (Authority and Format Identifier): Typically 49 for private IS-IS domains. Must be consistent within the domain.
• Area ID: Variable length. All L1 neighbors must share at least one area address to form L1 adjacency. L1/L2 and L2-only routers can have different area addresses and still form L2 adjacency.
• System ID: 6 bytes, must be globally unique within the IS-IS domain. Duplicate system IDs cause LSP wars — both routers originate LSPs with the same system ID but different content, causing continuous purge/regenerate cycles.
• NSEL (N-Selector): Must be 00 for the router itself. A non-zero NSEL identifies an upper-layer protocol endpoint, not the router.

Step 4: LSPDB Analysis

Examine the Link-State Protocol Data Unit database for integrity.

[Cisco]

text

show isis database detail | include LSP|Lifetime|Sequence

[JunOS]

text

show isis database extensive | match "LSP|Lifetime|Sequence"

[EOS]

text

show isis database detail | include LSP|Lifetime|Sequence

Assess LSPDB health:

• LSP count: Compare across neighbors in the same level — counts must match (LSPDB synchronization invariant). A mismatch indicates flooding failure or partition.
• Remaining lifetime: Default maximum is 1200 seconds. Originating routers refresh at 900 seconds (default). An LSP with lifetime near 0 that is not refreshed indicates the originator is unreachable. Lifetime at 0 means the LSP is being purged.
• Sequence numbers: Must increase monotonically. If the same system ID's LSP sequence number jumps backward, a router has restarted and is re- originating from a lower sequence number — or there is a system ID conflict.
• LSP purges: An LSP with remaining lifetime of 0 and empty TLV content is a purge. Frequent purges for the same system ID indicate instability — either the originator is flapping or two routers share the system ID (LSP war).
• Overload bit (OL): If set, SPF will not use this router for transit traffic. Check whether OL is intentional (maintenance, startup delay) or indicates a problem (memory exhaustion).

Step 5: Level 1/2 Routing and Route Leaking

Verify inter-level routing behavior at L1/L2 boundaries.

[Cisco]

text

show isis rib | include L1|L2|leak

[JunOS]

text

show isis route | match "L1|L2|leak"

[EOS]

text

show isis route | include L1|L2|leak

Validate inter-level behavior:

• L1→L2 redistribution: L1/L2 routers automatically redistribute L1 routes into L2 by default. Verify L1 prefixes appear in the L2 LSPDB. If missing, check for redistribution filters or route policies on the L1/L2 router.
• L2→L1 route leaking: Not automatic — requires explicit configuration. If configured, verify leaked L2 routes appear in the L1 RIB. Missing leaked routes indicate policy misconfiguration or the leak filter is too restrictive.
• Attached bit: L1/L2 routers set the Attached bit in their L1 LSP. L1-only routers use this to install a default route toward the nearest L1/L2 router. If no L1/L2 router has the Attached bit set, L1-only routers have no path out of the area. Verify with LSPDB detail — check the ATT flag on L1/L2 router LSPs.
• Suboptimal routing: L1-only routers always route toward the nearest L1/L2 router (default route). If there are multiple L1/L2 exit points, traffic may take a suboptimal path. Route leaking L2→L1 with specific prefixes fixes this by giving L1 routers more specific routing information.

Threshold Tables

Operational parameter norms for IS-IS — protocol-level expectations by network type and deployment scale.

Hello and Hold Timer Defaults:

Parameter	Cisco Default	JunOS Default	EOS Default	Notes
Hello (broadcast)	10s	9s	10s	Per-level configurable
Hello (P2P)	10s	9s	10s	Per-level configurable
Hold multiplier	3× hello	3× hello	3× hello	Dead = hello × multiplier
CSNP interval (DIS)	10s	10s	10s	Only DIS sends CSNPs
PSNP interval	2s	2s	2s	Request missing LSPs

LSPDB Norms:

Parameter	Normal	Warning	Critical
LSP max lifetime	1200s	—	—
LSP refresh	900s	Missed refresh	Lifetime < 300s
LSP remaining lifetime	300–1200s	60–300s	< 60s (near purge)
LSP purge rate	0/hour	1–5/hour	> 5/hour
LSPDB mismatch (neighbors)	0 LSP diff	1–3 diff	> 3 diff
Overload bit	Clear	Set (intentional)	Set (unintentional)

SPF Norms:

Parameter	Normal	Warning	Critical
SPF runs (per hour)	1–5	6–20	> 20
SPF initial delay	50–200ms	< 50ms	> 5000ms
SPF max hold	5000–10000ms	< 2000ms	> 50000ms
Convergence (single link)	< 1s	1–5s	> 10s

Metric Norms:

Metric Style	Range	Notes
Narrow (original)	1–63 per link	10-bit path metric max (1023)
Wide (extended)	1–16777215 per link	32-bit path metric — preferred
Transition	Both	During narrow→wide migration

Decision Trees

Adjacency Not Forming

text

IS-IS adjacency not reaching Up state
├── State: Down (no hellos received)
│   ├── Interface up? → Check Layer 1/2 status
│   ├── IS-IS enabled on interface? → Check IS-IS config on both sides
│   ├── Correct circuit type? → P2P interface must match both sides
│   └── Hello reaching peer? → Check ACLs, VLAN, encapsulation
│
├── State: Init (one-way hellos)
│   ├── Level mismatch?
│   │   ├── L1 needs same area → Compare area addresses in NETs
│   │   └── L2 allows different areas → Check both have L2 enabled
│   ├── Hello parameters?
│   │   ├── Authentication mismatch → Verify key/type per level
│   │   └── Hello interval incompatible → Not required to match but
│   │       hold time must exceed remote hello interval
│   ├── Interface type mismatch?
│   │   ├── P2P vs broadcast → Must agree on circuit type
│   │   └── Broadcast → DIS election proceeds after adjacency forms
│   ├── MTU issue? → IS-IS PDUs may be dropped if oversized
│   │   ├── Check interface MTU both sides
│   │   └── IS-IS does not negotiate MTU like OSPF — silent drop
│   └── Circuit type mismatch?
│       ├── L1-only ↔ L2-only → No common level → no adjacency
│       └── L1/L2 ↔ L1 → L1 adjacency forms; L2 does not
│
├── DIS election issue (broadcast only)
│   ├── DIS not elected? → Check priority (highest wins, then SNPA)
│   ├── DIS preemption → New higher-priority router takes DIS immediately
│   │   └── Unlike OSPF DR — IS-IS DIS is preemptive
│   └── Pseudonode LSP missing? → DIS must originate pseudonode LSP
│
└── Adjacency flapping (Up↔Down cycling)
    ├── Hello hold expiry → Check for packet loss or CPU overload
    ├── Authentication key rollover → Verify key transition timing
    └── Interface errors → Check CRC, input errors, drops

LSPDB Inconsistency

text

LSPDB mismatch or instability detected
├── LSP purge seen (lifetime = 0)
│   ├── System ID conflict? → Two routers with same system ID
│   │   ├── Both originate LSPs → Continuous purge/regenerate cycle
│   │   ├── Sequence numbers jump erratically → Confirms conflict
│   │   └── Fix: assign unique system IDs, check NET addresses
│   ├── Router departed gracefully? → Normal purge after shutdown
│   └── Router crashed? → LSP ages out (1200s) then purges
│
├── LSPDB count mismatch between neighbors
│   ├── MTU preventing LSP flooding? → Large LSPs dropped
│   │   ├── Check interface MTU across path
│   │   └── Enable LSP fragmentation or increase MTU
│   ├── Partition? → L2 backbone split → two independent LSPDBs
│   │   ├── Verify L2 connectivity between all L2 routers
│   │   └── Check for failed L2 link isolating a segment
│   └── Flooding blocked? → Authentication mismatch on one link
│       └── Adjacency up but LSPs rejected due to auth failure
│
├── Overload bit (OL) set
│   ├── Intentional? → Maintenance mode or on-startup timer
│   ├── Memory exhaustion? → Router cannot hold full LSPDB
│   └── Startup delay? → OL set for N seconds after process restart
│
└── Sequence number anomaly
    ├── Backward jump? → Router restarted, re-originating from lower seq
    ├── Rapid increment? → Frequent topology changes triggering re-origination
    └── Stuck at max? → Sequence wrap — extremely rare, requires process restart

Report Template

text

IS-IS ANALYSIS REPORT
======================
Device: [hostname]
Vendor: [Cisco | JunOS | EOS]
IS-IS Instance: [tag/instance name]
System ID: [system-id]
NET: [full NET address]
Check Time: [timestamp]
Performed By: [operator/agent]

ADJACENCY STATUS:
- Total adjacencies expected: [n]
- Up: [n] | Init: [n] | Down: [n]
- DIS role: [DIS for L1/L2 on segment X, or none]
- Adjacencies requiring attention: [list with states and levels]

LEVEL TOPOLOGY:
- Levels configured: [L1, L2, L1/L2]
- Area addresses: [list]
- Attached bit: [set/clear on L1 LSP]

FINDINGS:
1. [Severity] [Category] — [Description]
   Neighbor/Interface: [identifier]
   Observed: [state or metric]
   Expected: [normal state or value]
   Root Cause: [diagnosis from decision tree]
   Action: [recommended remediation]

LSPDB SUMMARY:
- L1 LSP count: [n] | L2 LSP count: [n]
- LSP purges in last hour: [count — 0 is healthy]
- Overload bit: [set/clear]
- Lifetime anomalies: [any near-expiry LSPs]

ROUTE ANALYSIS:
- L1 routes: [count] | L2 routes: [count]
- Route leaking: [configured/not configured — expected behavior]

RECOMMENDATIONS:
- [Prioritized action list]

NEXT CHECK: [CRITICAL: 1hr, WARNING: 8hr, HEALTHY: 24hr]

Troubleshooting

System ID Conflict (LSP War)

Two routers with the same system ID cause an LSP war — each router originates an LSP with the same system ID but different content. Each purges the other's LSP and regenerates its own, creating continuous churn. Symptoms: rapidly incrementing sequence numbers, frequent purge events, unstable routing. Detect by checking for the same system ID with two different SNPAs or source addresses in adjacency tables. Fix: assign unique system IDs.

Area Mismatch Preventing L1 Adjacency

L1 adjacency requires at least one matching area address in the NET. If two routers have different area addresses and are both L1-only, no adjacency forms. L1/L2 routers with different areas can still form L2 adjacency but not L1. Verify area addresses on both sides. Fix: correct the area address or change one router to L2-only if inter-area routing is the goal.

Metric Style Mismatch (Narrow vs Wide)

A router using narrow metrics (1–63) and a neighbor using wide metrics (1–16777215) may form adjacency but routes may not compute correctly if one side cannot interpret the other's TLVs. During migration, configure both sides for transition mode (advertise both narrow and wide TLVs). Verify with LSPDB detail — check for both old-style and extended IP reachability TLVs.

Authentication Mismatch

IS-IS supports per-level and per-interface authentication. A mismatch prevents adjacency formation (hellos rejected) or LSP flooding (LSPs rejected). Unlike OSPF where auth mismatch stops hellos, IS-IS can have adjacency up but LSP flooding blocked if hello auth succeeds but LSP auth fails. Check auth config at both hello and LSP levels independently.

LSPDB Overload from Excessive Redistribution

Redistributing large external route tables into IS-IS generates many LSPs, increasing LSPDB size, SPF computation time, and flooding overhead. Use route policies to limit redistribution scope. Consider setting the overload bit on non-transit routers that cannot handle the full LSPDB. Monitor LSP fragment count — each router can originate up to 256 LSP fragments (0–255).